Home   |   3D printer build surface

3D printer build surface

  • PEI Ultem sheet 305x305mm-0.2mm for CR-10
  • PEI Ultem sheet 305x305mm-0.2mm for CR-10
  • PEI Ultem sheet 305x305mm-0.2mm for CR-10
  • PEI Ultem sheet 305x305mm-0.2mm for CR-10
  • PEI Ultem sheet 305x305mm-0.2mm for CR-10
PEI Ultem sheet 305x305mm-0.2mm for CR-10PEI Ultem sheet 305x305mm-0.2mm for CR-10PEI Ultem sheet 305x305mm-0.2mm for CR-10PEI Ultem sheet 305x305mm-0.2mm for CR-10PEI Ultem sheet 305x305mm-0.2mm for CR-10

PEI Ultem sheet 305x305mm-0.2mm for CR-10

  • Material:Ultem/PEI/polyetherimide
  • Color:Amber
  • Thickness:0.125/0.175/0.2/0.8/1/2mm
  • Size:203x203mm,220x220mm,305x305mm Customized
  • INQUIRY BUY NOW

This PEI sheet is Pre-applied with 3M 468MP Adhesive Transfer Tape for your convenience.


PRODUCT SPECIFICATION

Material: PEI/ULTEM 1000/Polyetherimide

Color:Amber

Thickness: 0.125/0.175/0.2/0.8/1/2mm

Size:203x203mm,220x220mm,224x254mm,254x254mm,305x305mm,cut to small size and customized.

PEI (Polyetherimide) , also known as Ultem, is a reusable, relatively maintenance free, perfect build surface for both

ABS (with a Heated bed) and PLA (hot or cold), other materials such as Metal, Wood, ABS+ and many others also works just fine. PEI sheet is appealing due to its “no-surface-prep” conditions, which make it convenient to work with.Additionally, printing on PEI sheet requires no support rafts as parts adhere directly to the surface with no issue.


HOW TO USE:


This PEI sheet is specially made for Cr-10, Tevo Tornado, Hictop Prusa, and Lulzbot Taz or DIY 3d Printer . This PEI sheet is Pre-applied with 3M 468MP Adhesive Transfer Tape for your convenience. All you need is clean your 3D printer bed, so it is free of dust. Then peel off one side of 3M 468MP Adhesive and slowly and evenly use a flat card to sweep the PEI sheets to the build bed. Make sure there is no bubble ( it is very rare it will has a bubble ), also keeping in mind that 3M 468MP is a very sticky tape that is prone to clumping.

Sanding the PEI is not required or necessary, but sanding with a fine grid sandpaper will help the part stick better to the PEI build surface.

Once you have laminated your PEI sheet onto your print bed, simply re-level your print bed and print away. Parts should come free from the surface with almost no issue at all. PLA does not require heat, but turning the heated bed up to 60 °C work best with PEI.

PEI sheet work perfectly well with ABS for delta printer with 100-110 °C. After the print is done, just let the PEI sheet cool down and then gently you can just “pop” the finish print off the plate easily.










Contact Us

Contact: Mozart Jiang

Phone: 18923742060

Tel: 0755-89664362

Add: Room 8103, Jinmaoyuan Building, Jinniu Western Road, Pingshan District, Shenzhen, China 518118

Scan the qr codeClose
the qr code